Easy DIY Outdoor Chairs

by Marina Ingrit

It has been a couple of years since I shared this project. This is the perfect time of year to start a project like this so I am sharing it again. I only made 4 last time so I think I am going to build some more DIY outdoor chairs this summer. We are lucky enough to have a nice fire pit in the backyard. Having four boys who love all things outdoors, we use it all the time. Up until now, we have lugged out the dining room chairs every time we use the fire pit. I finally broke down and decided that building some chairs needed to be pushed to the top of my to-do list. Here is how I made these super easy DIY outdoor chairs!

alt

alt

 

A long time ago I built a bench for Shane’s brother and his wife for their new home. I liked the design I came up with so much that I decided to use it for these chairs. I liked that the bench was deep enough that adding a pillow didn’t make you feel like you were sitting on the edge of the seat. And since it’s made from 1x4s and 2x4s, it’s very sturdy and won’t blow away every time it gets a little windy.

 

Cut list per chair:

(11) 18” 1x4s – slats for seat and back

(2) 22” 2x4s – front and back connector

(2) 38” 2x4s – back legs and back

(2) 17” 2x4s – front legs

(2) 15” 2x4s – finishes off sides

(1) 18” 1×3 – caps off top of chair for a finished look

(1) 15” 1×3 – added to back of chair

DIY Outdoor Chairs – Assembly

Step 1:

I started by cutting two pieces of 2×4 to be 38 inches high and two pieces to be 17 inches high. The 38-inch boards will be the back and the 17-inch-high boards will be the front legs. Then I cut two 22-inch boards. These will connect the front and the back and determine how deep your chair is. If you don’t plan on having pillows and want it a bit shallower, 18 inches would be a good depth too.

 

alt

 

Step 2:

I wanted the back slightly slanted so it would be more comfortable. I measured and marked the center of the top of the back 2x4s, then used a straightedge to draw a line down to the bottom where the seat will be.

 

alt

 

I used my jigsaw to cut along the line, then sanded it after cutting.

 

alt

 

Step 3:

Now it’s time to attach all the 1×4 boards. I cut 11 boards to be 18 inches long, attached the front pieces first to the leg pieces as shown below, then added the back piece.

 

alt

 

By adding the front and back pieces of the seat first, you can then fill in the center and make sure the gaps are all equal. I eyeballed it, although the measurement will be about ½ inch.

 

Step 4:

Once the seat boards are attached with wood screws, you can start the back. I started with the lowest one. Instead of having it flush against the seat board, I made a ½ gap.  I added the top back board next so I could then fill in the middle like the way I did the seat.

 

alt

 

Step 5: (*optional)

Now that the chair is basically assembled, it’s time to add some boards that will give it a more finished look. Cut a 2×4 board to fit inside the legs and attach one to each side.

 

alt

 

I added a 1×3 to the top and to the back of the seat like shown below.

 

alt

 

alt

 

DIY Outdoor Chairs – Finishing

The chair is completely assembled! It is really a pretty easy build. I built all four in one day.

Step 1:

Once the chair is done you will want to use a hand sander to remove any inked-on text from the wood, then hand sand the whole chair. 1x4s have a waxy feel and won’t absorb stain well unless you sand and open the pores. Wherever you used the hand sander, make sure to hand sand after really well or you will be able to see the circular marks made by the sander when you begin to stain. Start with a 100 grit then finish with a 150 or 220.

 

alt

 

Step 2:

Dust the chair off and you are ready to stain! I used the same color that I used on my planter box fence last month. I loved the look of Thompson’s WaterSeal Penetrating Timber Oil Semi-Transparent in Walnut.  The color is dark and rich, but still allows the wood grain to show through.

 

alt

 

To apply the stain, I used a brush that is designed for use with oil-based paints and stains. Using a brush made it easy to stain the ½” gaps between the boards.

Allow the chairs enough time to dry before using them. The can recommends letting the stain dry for 24 hours to cure completely.

 

alt

 

 

They fit around our firepit nicely!

 

alt

 

Once they were dry, we were able to test them out. Someone who shall remain nameless (*cough cough Shane*) ate the marshmallows before we could roast them, but hot dogs for dinner is always a hit.

 

alt

 

Do you have enough outdoor seating? What type of outdoor seating do you have?

 

PIN For Later:

alt

 

 

You may also like